微型计算机常见屏幕信息详解PDF|Epub|txt|kindle电子书版本网盘下载

微型计算机常见屏幕信息详解PDF格式电子书版下载

注意：本站所有压缩包均有解压码： 点击下载压缩包解压工具

第一编 使用MS-DOS操作系统命令屏幕常见信息1

第一章 屏幕常见错误信息及处理方法1

第一节 系统启动时屏幕常见错误信息1

1．Bad Command or file name2

2．Bad or missing Command Interpreter2

3．Bad or missing keyboard Definition File3

4．Boot Failare3

5．Boot Failare-Insert System Disketter，then press3

6．CMOS is not properly setup4

7．CMOS memory configration is invalid-SETUP must be run4

8．Filename code page driver cannot be initialized4

9．Diskboot failture4

10．Drive Not Ready Error，Insert Boot Diskette A：4

11．Enter correct name of Command Interpreter（eg，c：COMMANDCOM）4

1 2．Error：Can’t enable A20 ！ XMS Drive not installed5

13．Error Loading oprating system5

14．Extender Card Switch do not match system memory Size5

15．Insufficient memory5

16．Invalid COMMAND．COM6

17．Keybord error6

18．Keybord is locked Unlock it6

19．No Rom BASIC system Hilted6

20．Non-System disk or disk error6

21．Not ready error A：Abort，Retry，Ignore？7

22．Required font not loaded7

第二节 环境配置屏幕常见错误信息7

1．Bad Command or paratmeters7

2．Bad or missing ANSISYS8

3．Bad or missing file name8

4．Buffer size adjusted8

5．CACHE Already Installed8

6．CACHE Not Installed9

7．CACHE Not Installed-Cache Too Large9

8．CACHE Not Installed-Expanded Memory Error9

9．CACHE Not Installed-Expanded memory Not Available9

10．CACHE Not Installed-Extended memory Not Available9

11．CACHE Not Installed-Incorrect DOS Version10

12．CACHE Not Installed-Invailable Parameter10

13．Configration too large for memory10

14．Driver not installed-Microsoft Mouse not found10

15．Error：An XMS manager is already installed XMS Drive not installed10

16．Error：Available extended memory was not found XMS Driver not installed11

17．Error：Cannot unmap the Shadow ROM XMS Driver not installed11

18．Error：HIMEMEXE requres DOS 3．0 or higher XMS Driver not installed11

19．Error：Invalid command line parameter XMS Driver not installed11

20．Error：LEAVE parameter value out of range11

21．HMA not available：loading DOS low12

22．Incorrect machine type12

23．Incorrect order in CONFIGSYS LINE n12

24．Insufficient memory12

25．Invalid STACK parameters13

26．Invalid switch character13

27．Invalid syntax DISPLAYSYS code page driver13

28．Invalid syntax PRINTERSYS code page driver13

29．Secondary controller board error13

30．Sector size adjusted13

31．Sector size too large in file filename14

32．Timeout on disk x，secondary controller14

33．Too many block devices14

34．Unrecognuzed command in CONFIGSYS14

第三节 文件管理屏幕常见错误信息14

1．Access denied14

2．Filename-Access denied15

3．A filename with that first character already exists15

4．Bad command line syntax15

5．Bad Command or file name15

6．Bad numeric argument16

7．Bad or missing Command Interpreter16

8．Bad or missing Keybord Definition File16

9．Cannot DISKCOPY to or from a network drive16

10．Cannot DISKCOPY to or from an ASSIGNED or SUBSTED drive17

11．Cannot do binary reads from a device17

12．Cannot edit BAK file-rename file17

13．Cannot find FORMAT．COM17

14．Cannot find GRAPHICS profile18

15．Cannot find System files18

16．Cannot format an ASSIGN or SUBST drive18

17．Cannot FORMAT nonremovable drive X18

18．Cannot LABEL a SUBSTed or ASSIGNed drive18

19．Cannot load COMMAND，system halted19

20．Cannot operate on specified drive（X）It may be a network19

21．Cannot operate on a SUBST drive19

22．Cannot open list device PRN Enter name of list device？19

23．Cannot open run/temporary file19

24．Cannot perform a cyclic copy20

25．Cannot read file alloction table20

26．Cannot RECOVER an ASSIGNed or SUBSTed drive20

27．Cannot read system area of disk20

28．Cannot specify both/DT and/DOS21

29．Cannot specify default drive21

30．Cannot start COMMAND，exiting21

31．Cannot SYS a SUBSTed or ASSIGNed drive21

32．Cannot unload resident delete-tracking software Vectors or21

memory have been altered21

33．Cannot use FASTOPEN for drive X21

34．Cannot write file allocation table22

35．Cannot XCOPY from a reserved device22

36．Cannot XCOPY to a reserved device22

37．Can’t find/open file：filename22

38．Can’t read file：filename22

39．CHKDSK not available on drive X：22

40．content of destination lost before copy23

41．Convert lost chain to files（Y/N）？23

42．could not expand second filename so as to match first23

43．Data error23

44．Delete-tracking file not find23

45．Disk error reading FAT n24

46．Disk error writing FAT n24

47．Disk fullEdits lost24

48．Disk full error writing to BACKUP Log File，Press any key to continue24

49．Divide overflow24

50．Do not specify filename（s）24

51．Do not specify filename（s）Command format DISKCOPY d：d：［/1］25

52．DOS verion must be 2.0 or later25

53．Drive formatted with a DOS version prior to 3．X restore prior DOS with SYS，backup files，boot with 5.0．and create a 5.0．based partition25

54．Drive X error，Could not open the mirror25

55．Drive X error Insufficient space for the mirror file25

56．Drive X error，Could not close the mirror25

57．Drive X error Insufficient memory to read all system info26

58．Drive X error The boot sector for this drive is incompatible with the mirror command26

59．Drive X error Insufficient space for the mirror control file26

60．Drive X errorWe were unable to find the mirror image file in the root directory of the hard drive26

61．Drive X errorCannot update the mirror control file26

62．Drive X error There is already a mirror control file，but it was not located in the last 25．percent of the data area It has now been deleted and processing will continue26

63．Drive X error Data was found in a file that appears to be a mirror control file Cannot continue26

64．/DT was specified Because there is no delete-traking file for this drive the UNDELETE command cannot continue27

65．Dublicate file name or file not found27

66．Dublicate Parameters not allowed27

67．Entry has a bad link27

68．Entry has a bad size27

69．Error executing FORMAT27

70．Error reading GRAPHICS profile28

71．Error reading system areas28

72．Error reading the file28

73．Error writing fixed disk28

74．Error writing system areas28

75．Error writing the mirror file28

76．Error found，F parameter not specified Correctionswill not be written to disk29

77．FCB unavailable29

78．FC：Cannot open filename-No such file or directory29

79．FC：filename1．longer than filename229

80．FC：Incompatible switches29

81．File allocation table bad drive d29

82．File allocation table bad30

83．File cannot be converted30

84．File cannot be copied onto itself30

85．File creation error30

86．File is READ-ONLY30

87．File must be specified31

88．File not found-filename31

89．filename contains nnnn non-continuous blocks31

90．FIND：Invalid number of parameters31

91．FIND：Invalid parameter31

92．FIND：Read error in filename31

93．First allocation unit is invalidentry truncated31

94．First diskette bad or incompatible32

95．Fixed backup device D：is full32

96．Font file contents invalid32

97．Has inalid allocation unit，file truncated32

98．Inconsistencies found in DOS Boot Record32

99．Inconsistencies found in DOS Boot RecordUse CHKDSK/F to correct inconsistencies32

100．Incompatible file version＃33

101．Incorrect APPEND version33

102．Incorrect DOS version33

103．Incorrect drive syntax-x33

104．Insufficient disk space33

105．Insufficient disk on disk33

106．Insufficient room in root directory Move files root directory and repeat CHKDSK33

107．Internal stack overflow system halted34

108．Invalid boot record signature34

109．Invalid Date/Time34

110．Invalid drive in search path34

111．Invalid drive specification Specified drive does not exist，or is non removeable34

112．Invalid filename or file not found34

113．No entries found35

114．No file added35

115．No file found-filename35

116．No partitions to save35

117．No subdirectory exist35

118．No system on default drive35

119．Non-standard Missing or bad partition table35

120．＊＊＊Not able to backup file＊＊＊36

121．path not found36

122．Parameter value not allowed36

123．Parameter value not in allowed range36

124．Probable non-DOS disk Continue（Y/N）？36

125．Program too big to fit in memory37

126．Read fault error37

127．Read fault error reading drive X：37

128．Required parameter missing37

129．Restore file sequence error37

130．Resynch failed Files are too different38

131．Source and target drive are the same38

132．SOURCE diskette bad or incompatible38

133．Source diskette bad or unusable38

134．Source does not contain backup files38

135．Source path required39

136．Secified COMMAND search directory bad39

137．Target cannot be used for backup39

138．Target diskette may be unusable39

139．Target diskette unusable39

140．The last file was not restored39

141．unable to write BOOT39

142．Unrecoverable error in directory Convert directory to file（Y/N）？40

143．Unrecoverable read error on drive X size Y，track Z40

144．X lost allocation units found in Y chains Convert lost chains tofiles（Y/N）？40

第四节 磁盘目录管理屏幕常见错误信息40

1．Attempt to remove current directory40

2．Cannot CHDIR to root41

3．Cannot make directory entry41

4．Cannot recover…entry41

5．Directory already exists41

6．Directory is joined，tree past this point not processed41

7．Directory is totally empty，no．or．．tree past this point not processed41

8．Directory not empty42

9．Does not exist42

10．Drive X error There are no entries available in the root42

11．Error reading directory42

12．Error writing dirctory（FAT or fixed disk）42

13．Invalid current directory42

14．Invalid directory43

15．Invalid drive and/or path43

16．Invalid drive in search path43

17．Invalid path or filename43

18．Invalid path，not all directories/files copied43

19．Invalid path，not directory or directory not empty43

20．No Room in directory for file44

21．Source path required44

22．Specified COMMAND search directory bad44

23．unable to creat directory44

24．Unrecovered error in directory44

第五节 磁盘管理屏幕常见错误信息45

1．All available space in the Extended DOS Partition is assigned to logical drives45

2．Attempting to recover allocation unit45

3．Bad Partition table45

4．Cannot creat a zero size partition46

5．Cannot create Extended DOS Partition without Primary DOS Partition on disk 146

6．Cannot create Logical DOS Drive without an Extended DOS Partition on the current drive46

7．Cannot delete Extended DOS Partition while logical drive exist46

8．Cannot delete Primary DOS Partition on drive 1．when an Extended DOS Partition exits46

9．Cannot format an ASSIGNed or SUBSTed drive46

10．Cannot read system area of disk46

11．Disk error reading（or writing）FAT X47

12．Error loading operating system47

13．Error reading directory47

14．Error reading fixed disk47

15．Error reading partition table47

16．Error reading file48

17．Error writing directory48

18．Error writing FAT48

19．Error writing fixed disk48

20．Error writing partition table48

21．Format terminated49

22．Invalid device parmeters from device driver49

23．Invalid entry，please enter x-y49

24．Invalid entry，please press ENTER49

25．Invalid media or Track 0．bad-disk unusable49

26．Invalid options49

27．Invalid or unspecified drive49

28．Invalid partition table50

29．Invalid volume ID50

30．Invalid volume label50

31．Maximum number of logical DOS drives installed50

32．Missing operating system50

33．No fixed disks present51

34．No hard drive found51

35．No Logical DOS Drive（s）to delete51

36．No Non-DOS partition to delete51

37．No partitions to delete51

38．No partition to make active51

39．No room for system on destination disk52

40．No space for a nnnn cylinder partition52

41．No space to create a DOS partition52

42．Only non-startable partitions exist52

43．Only partitions on Drive 1．can be made active52

44．Parmeters not compatible52

45．Parameters not compatible with fixed disk52

46．Parameters not supported by drive53

47．Partition selected is not a primary DOS partition53

48．Partition selected is not a Non-DOS partition53

49．Partition selected（X）is not startable，active partition not changed53

50．Primary DOS partition already exists53

51．Requested logical drive size exceeds the maximum available space53

52．Requested partition size exceeds the maximum available space54

53．Same parameter entered twice54

54．The Master Boot code has NOT been updated54

55．The only startable partition on Drive 1．is already set active54

56．Track 0．bad-disk unusable54

57．Unable to access drive D54

58．Unable to write BOOT54

59．Wrong DOS Version55

第六节　批处理文件屏幕常见错误信息55

1．Bad command or filename55

2．Bad command or parameters55

3．Bad or missing Command Interpreter55

4．Batch file missing56

5．Connot load COMMAND，system halted56

第七节　输出管理屏幕常见错误信息56

1．B Invalid with a black white printer56

2．Cannot use PRINT-use NET PRINT56

3．Error on list device indicate that it may be off-line please check it56

4．Invalid switch-/T〈filename〉57

5．List output is not assigned to a device57

6．nnn error file filename57

7．No paper57

8．NOT A GRAPHICS PRINTER FILE57

9．Path not found-〈filename〉57

10．Path name too long58

11．Printer out paper error58

第八节 系统配置屏幕常见错误信息58

1．Bad command or parameters58

2．Buffer size adjusted58

3．Configuration too large for memory59

4．Cannot start COMMAND exiting59

5．Error in CONFIG．SYS line x59

6．EXEC failure59

7．Fatal：internal stack failure，system halted60

8．Insufficient memory60

9．Invalid STACK parameters60

10．Invalid syntax on DISPLAYSYS code page driver60

11．No drive specified60

12．No free file handles61

13．No more files61

14．System resource exhausted61

15．Too many open files61

16．VDISK not installed-Insufficient memory61

第二章屏幕常见提示信息63

第一节 系统启动屏幕常见提示信息63

1．nnnKB CACHE MEMORY63

2．Hit＜DEL＞，if you want to SETUP63

3．Current date is Tue 05-09-1995．Enter new date（mm-dd-yy）63

4．Current time is 3：47：3941p Enter new time：63

5．Fastopen already installed64

6．There is not enough free space on drive C to install MS-DOS64

7．You computer uses password protection64

第二节 环境配置屏幕常见提示信息64

1．APPEND already installed64

2．ANSI．SYS must be installed to perform requested function64

3．Break is OFF｜ON64

4．Cannot setup expanded memory65

5．Incorrect APPEND version65

6．Insert disk with command in drive X，strike any key when ready65

7．Invalid environment size specified65

第三节 文件管理屏幕常见提示信息65

1．Amount read less than size header65

2．All files in directory will be deleted！65

3．Cannot execute XCOPY65

4．Cannot recover entry，processing continued66

5．Cannot use FASTOPEN for drive X：66

6．Content of destination lost before copy66

7．Volume in drive X is SSSS66

8．Diskette compare OK66

9．Does name specify a file name or directory name on the target（F＝file，D＝directory）66

10．File cannot be copied onto itself66

11．Incompatible system size67

12．Insert SOURCE diskette in drive A：67

13．Insert system disk in X and strike any key when ready67

14．Insert target disk in drive A，press any key when ready67

15．Insufficient memory for system transfer68

16．Invalid characters in volume label68

17．Press CTRL＋C to abort，or correct this problem and press any other key to continue68

18．Reading source file（s）68

19．Replace filename（Y/N）？68

20．Second diskettebad or incompatible68

21．System transfered68

22．Target diskette write protected，correct then strike any key68

23．The filename already exists Type another filename press F5．to bypass this file69

24．Volume Serial Number is XXXX-XXXX69

25．Warning All data on non-removable diskdrive X will be lost proceed with FORMAT（Y/N）？69

26．Warning！File X is read-only file69

27．Warning ！ Read error in EXE file69

28．Write protect error69

29．Your computer is running with an incompatible version of DBLSPACEBIN69

第四节 目录管理屏幕常见提示信息69

1．Array element size mismatch70

2．Attemp to access data outside of segment bounds70

3．Cannot open run file70

4．Cannot open temporary file70

5．CHKDSK failed，trying alternate Method70

6．Does name specify a file name or directory name on the target（F＝file，D＝directory）70

7．DOS（．）（．．）not exist70

8．Insufficient room in root directory，erase files from root and repeat CHKDSK71

9．Invalid path on directory or directory not empty71

10．Invalid sub-directory entry71

11．No subdirectory exist71

12．Too many file/directory entries71

第五节 磁盘管理屏幕常见提示信息71

1．All logical drive in the extanded DOS partition71

2．Bad tracks found at start of partition．Partition size adjusted71

3．Convert lost chains to files（Y/N）71

4．Copy another diskette（Y/N）？72

5．Copying t track n sectors/track，s side72

6．Disk not compatible72

7．Disk unsuitable for system disk72

8．Drive X already deleted72

9．Drive deleted72

10．Error reading/writing partition table72

11．Extended DOS partition already exists72

12．Extended DOS partition created73

13．Extended DOS partition deleted73

14．Incompatible hard disk or device drive73

15．Incompatible primary DOS partitionrive73

16．Invalid disk change73

17．Invalid media or track 0．bad-disk unusable73

18．Invalid media type73

19．X is not choice，please entry Y-Z73

20．Must enter both/t and/N parameter73

21．No extended DOS partition to delete74

22．Nopartition to make active74

23．No primeary DOS partition to delete74

24．Only non-bootable partition exist74

25．Not ready error reading（or writing）drive X：74

26．X percent of disk formatted74

27．Press any key to be formatting X：74

28．Requested logical drive size exceeds the maximumavailable space74

29．The current active partition is X：75

30．The only bootable partition on drive 1．is already set active75

31．Warning！All data on non-removeable disk drive X will be lost proceed with FORMAT（Y/N）？75

32．Warning！Data in DOS Partition could be DESTROYED Doyou wish to continue？75

33．Warning！No partition are set active-disk is notstartable unlessa partition is set active75

34．Cannot find a hard disk on your computer75

35．Too many primary partition76

第六节 批处理文件屏幕常见提示信息76

1．Insert disk with batch file and strike any key when ready76

2．Terminated batch job（Y/N）？76

第七节 输出管理屏幕常见提示信息76

1．All files canceled by operator76

2．File filenameext cancelled by operator76

3．Filenameext is currently being printed76

4．LPT＊：rerouted to COMn76

5．LPT＊set for 8077

6．LPT＊set for 13277

7．Name of list device［PRN］：77

8．Rcsident part of print installed77

9．〈filename〉is currently being printed77

10．Print queue is empty77

第八节 系统配置屏幕常见提示信息78

1．Loaded external disk driver for drive D：78

2．VDISK nott installed-Iusufficient memory78

3．VDISK Version 5.0 Virtual disk X：78

第二编 使用WPS编辑软件屏幕常见错误信息79

第三章 启动SPDOS汉字系统屏幕常见错误信息79

第一节 启动SPDOS各版本的方法79

1．SPDOS4.3的启动方法79

2．SPDOS5.0的启动方法79

3．SPDOS5.1的启动方法79

4．SPDOS6.0F的启动方法79

5．UCDOS3.0以上版的启动方法79

第二节 启动SPDOS汉字系统屏幕常见错误信息80

1．C：XSDOS．LPH not found or read error80

2．SuperChincse Card-H has not been installed！80

3．Vidcoo parameter not set！80

第四章 运行WPS编辑软件常见错误信息82

第一节 启动WPS的方法和参数82

1．在SPDOS下启动WPS编辑软件82

2．UCDOS3.0以上版汉字系统下启动WPS编辑软件82

第二节 使用WPS编辑软件常见错误信息及处理82

1．File SPDOS．COM not found！82

2．SUPER-CCDOS版本不兼容82

3．WPS1．OVL版本不兼容83

4．WPS2．OVL版本不兼容83

5．WPS1．OVL not found！83

6．WPS2．OVL not found！83

7．Please run RDSL.COM first！83

8．启动WPW后出现死机83

9．文件名字错误84

10．文件名包含非法字符84

11．不能编辑BAK文件，按任意键将继续84

12．不能打开％？％文件84

13．源文件找不到84

14．文件包含非法字符85

15．文件不存在85

16．密码错误85

17．Invaild parameter for wps！85

18．建立文件错误85

19．WPS内部错误，并给出错误地址86

20．WPS被非法终止86

21．内存不够，按任意键将继续86

22．内存使用溢出87

23．窗口定义已满87

24．不能分割屏幕87

25．文件已经打开87

26．磁盘满，按任意键将删除．BAK文件87

27．没找到88

28．数字超出范围88

29．行数超出范围88

30．表格太大88

31．块没有定义，按任意键将继续88

32．屏幕块没有定义88

33．首尾不对齐89

34．块太大89

35．块首没有定义89

36．块尾没有定义89

第三编 使用压缩软件屏幕常见错误信息90

第五章 使用ARJ压缩软件屏幕常见错误信息90

第一节　ARJ命令格式及常用参数90

第二节　使用ARJ压缩软件屏幕常见错误信息92

1．Archive name argument missing92

2．Arg table overflow93

3．Bad command syntax93

4．Bad file data93

5．Bad file data or password93

6．Bad header93

7．Can’t delete〈filename〉93

8．Createarchive：〈filename〉93

9．Can’t open file skipped〈filename〉94

10．Can’t write file，Disk full？94

11．Can’t find〈filename〉94

12．can’t find restart file＜filename＞94

13．Can't rename ＜filename＞to＜filename＞94

14．Can’t use-v with self-extraction94

15．Can’t reset＜filename＞95

16．＜filename＞does not exist95

17．＜filename＞exist95

18．＜filename＞is not an ARJ archive95

19．＜filename＞is not the same date/time95

20．＜filename＞is same or newer95

21．FKSKX：Warning！files fails CRC check95

22．〈filename〉is same or newer overwrite？［YNAQ］96

23．Delete argument missing96

24．Exceeded maximum path size of＜number＞at〈filename〉96

25．File is password encrypted96

26．Invalid command：＜command＞96

27．Invalid comment header96

28．Invalid date string：＜date＞97

29．Invalid multiple volume file sequence97

30．Invalid parameter string：＜parameter＞97

31．Invalid switch：＜option＞97

32．Invalid volume size97

33．Missing filename argument for＜command＞97

34．Multiple volume updates are NOT supported97

35．Nothing to do98

36．Not enough disk space for extraction，Overflow by over＜number＞bytes98

37．Not enough disk space98

38．Not enough free disk space98

39．Out of memory98

40．Password option missing98

41．Password did not match98

42．Read/Write error＜message＞on＜drive＞98

43．Unknown file type：＜number＞99

44．Unknown method：＜number＞99

45．Unknown version：＜number＞99

46．Warning！ Only＜number＞bytes of free disk space continue？99

47．Not a valid method for SFX99

第六章 使用PKZIP和PKUNZIP压缩软件常见错误信息100

第一节 PKZIP和PKUNZIP命令格式及常用参数100

第二节 使用PKZIP压缩文件常见错误信息101

1．Nothing to do101

2．No files specified for deletion！101

3．No file found101

4．Disk full，file：〈filename〉102

5．Too many files102

6．Can’t open XXXX．ZIP for write access！102

7．Insufficient disk space for updated files：XXXX．ZIP102

8．Insufficient memory102

9．Warning！Can’t delete XXXX102

10．Insufficient disk space for ZIP comment103

第三节 使用PKUNZIP常见错误信息103

1．Pkunzip：Warning！Skipping encrypted file：〈filename〉103

2．Warning！File XXXX already existsOverwrite（y/n）？103

3．Warning！File has bad table103

4．Warning！No file（s）found103

5．Disk full，file：〈filename〉103

6．Can’t open XXXX103

7．Warning！Insufficient memory104

8．Warning！Can’t create：XXXX104

9．Incorrect password for file104

10．Warning！I don’t know how to handle104

第七章 ICE压缩软件使用及常见错误信息105

第一节 ICE命令使用格式及参数105

第二节 使用ICE压缩文件常见错误信息105

1．Achive not found〈filename〉105

2．Bad file data106

3．Can’t write file106

4．Invalid switch106

5．No file found106

6．No file name106

附录：ARJ、PKZIP、ICE功能比较列表107